Discoveryopt DGPR3 – Medium Universal Mount for 30 mm and 1-Inch Tubes
The Discoveryopt DGPR3 is a premium two-piece pair of scope rings for Picatinny rails. The rings are made for 30 mm tubes as standard, and with the supplied precision-machined aluminium reducer insert they also fit riflescopes with a 1-inch (25.4 mm) tube. One mount therefore stays useful even if you use several riflescopes with different tube sizes.
One Mount, Two Tube Sizes
The reducer insert is not plastic but machined aluminium with a polished inner surface, so the tube rests on a metal surface rather than on a soft liner. For 1-inch tubes use the rings with the insert; for 30 mm tubes remove the insert.
Medium Mounting Height
The tube centreline sits 1.26" (32 mm) above the Picatinny rail. This medium height leaves enough room for riflescopes with a larger objective, while the riflescope still stays relatively close to the rifle.
The maximum front lens diameter is 62 mm. This is the outer diameter including the lens cap, not the nominal optical diameter. At this diameter the riflescope clears the rail by approx. 1 mm. If your riflescope's objective is larger, choose a taller mount; if it is much smaller, the low version may be the better choice.
Design and Material
- 6061-T6 aluminium — the lower and upper half of each ring are each CNC-machined from a single block
- Hard-anodised finish — wear-resistant, matte black coating
- Three screws per side — the screw positions are numbered, making it easy to keep an even, controlled tightening sequence
- Engraved markings — the tube size, height and torque value can be read on the ring, so there is no need to look for the manual
- No built-in cant — 0 MOA; any inclination comes from the rail on the rifle
- Shock resistance — 1000 G according to the manufacturer
Picatinny Rails Only
The DGPR3 mounts on Picatinny (MIL-STD-1913) rails only, not on Weaver rails. The two rails look similar at first glance, but the slot width and spacing may differ, so choose this mount for Picatinny rails only. If you are not sure which rail your rifle has, write to us and we will gladly help you identify it.
Installation and Torque
The manufacturer's maximum values are: 25 in-lbs (approx. 2.8 N·m) for the screws that clamp to the rail, and 20 in-lbs (approx. 2.3 N·m) for the screws that hold the tube. On a rifle with lighter recoil you may lower these slightly, but always evenly, to the same value on every screw. Tighten the screws gradually, following the engraved numbering.
As these are relatively low torque values, it is worth using a precise torque screwdriver. Typical torque wrenches are often inaccurate in this range. It is also worth checking the screws after the first few shots.
Technical Specifications
- Model — DGPR3
- Manufacturer — Discoveryopt
- Tube diameter — 30 mm (without insert) and 1 inch / 25.4 mm (with reducer insert)
- Tube centre height — 1.26" (32 mm)
- Rail — Picatinny (not Weaver)
- Design — two-piece ring pair, medium
- Material — 6061-T6 aluminium, aluminium reducer insert
- Finish — hard-anodised
- Max. front lens diameter — 62 mm (including lens cap)
- Max. torque — 25 in-lbs (to the rail), 20 in-lbs (on the tube)
What's in the Box
- Mount — 1 pair (two rings with reducer insert)
- Torx (star) key — 1 pc
The riflescope is not included.
Who Is It For?
The medium version of the DGPR3 is recommended for anyone looking for a medium-height, Picatinny-only mount for a 30 mm or 1-inch riflescope, especially if the front lens is larger (up to 62 mm). It is a good choice if you use several riflescopes or may change tube size later, because you can keep using the same pair of rings. It also suits hunters and sport shooters who like clear, engraved torque markings.
Customer Experience
The DGPR3 series is still new, and there is not enough independent feedback for it yet. The summary below is based on customer reviews of other (7075) models in the Discoveryopt ring family, so it reflects the family's general experience.
Customers most often point out the clean machining and the precise fit. One customer who works in gunsmithing found that the rings fitted the tube well without lapping. Several praise the value for money and see the torque values engraved on the ring as an advantage. Source: Amazon customer reviews and customer reviews on the manufacturer's web shop.
Join our Facebook and YouTube channels!
Facebook page: https://www.facebook.com/riflescopeshop
Facebook group: https://www.facebook.com/groups/riflescopeshop
YouTube channel: https://www.youtube.com/@riflescopeshop
Any questions?
Contact us through the web shop and we will help you choose the best solution for your riflescope and rifle!