Detailed description

Discoveryopt One-Piece Cantilever 20 MOA Scope Mount for 30 mm Tubes, for Picatinny Rail

The Discoveryopt one-piece cantilever scope mount is made for scopes with a 30 mm tube and 20 mm Picatinny rails. Both rings are part of a single CNC-machined aluminum body, and the built-in 20 MOA cant gives the scope more adjustment reserve at longer distances. This is a high version, with the tube center approx. 39 mm above the rail.

What does the built-in 20 MOA cant mean?

The mount tilts the scope forward and downward relative to the barrel by 20 MOA. That is about 58 cm at 100 meters, or about 5.8 MIL. You need to dial that much less on the turrets when shooting at long range, so more of the scope's adjustment range is left for distance corrections. The cant does not replace a scope with a suitable adjustment range, it only shifts the usable range.

Cantilever design and eye relief

With a cantilever design the rings extend ahead of the base (the overhang is approx. 36.6 mm), so the scope can be placed further forward on the rail. This is especially useful on rifles with a long, continuous rail, such as AR-type rifles. The right eye relief depends on the scope, the shooter's build and shooting position, so it is worth testing the position before final tightening.

Construction and material

According to the manufacturer, the mount is CNC-machined in one piece from 6061-T6 aluminum, with a matte hard-anodized finish. The base has three recoil lugs that sit in the slots of the Picatinny rail and help the mount stay in place.

Key data before you buy

  • Tube diameter — 30 mm
  • Rail — 20 mm Picatinny only (MIL-STD-1913)
  • Cant — 20 MOA built in
  • Design — one-piece, cantilever, high
  • Tube center height — approx. 39 mm
  • Mounting length — approx. 91.8 mm
  • Overall length — approx. 128.4 mm
  • Ring width — approx. 22 mm per ring
  • Distance between rings — approx. 66 mm
  • Objective lens — up to approx. 74 mm outer diameter (including lens cap)

Objective size and ring placement

The 74 mm figure refers to the total outer diameter of the scope including the lens cap, not the nominal optical diameter of the lens. The maximum size also depends on how the scope is mounted, but in principle a total outer diameter of 74 mm still fits, so the mount can be recommended for larger objectives too. In that case a test fit is strongly advised. There is approx. 66 mm of free space between the two rings, each about 22 mm wide, so before buying please check that the scope tube has room for both rings without the turret or lens housings getting in the way.

Picatinny rail, not Weaver

This mount fits only 20 mm Picatinny (MIL-STD-1913) rails. Picatinny and Weaver rails are often confused, but Weaver cross slots are not uniform in width and the recoil lugs of this mount are made for Picatinny slots, so we do not recommend it for Weaver rails. It does not fit 11 mm dovetail rails. If you are unsure about the rail on your rifle, write to us and we will help you find out.

Installation and torque

For the ring screws, the manufacturer specifies 18 in-lbs (approx. 2.0 N·m). For the screws that secure the mount to the rail, the manufacturer's value is 30 in-lbs (approx. 3.4 N·m), which we consider high, justified at most on larger calibers (for example .308 or .30-06). On smaller calibers with lighter recoil, a lower torque is enough. At such low values, typical torque wrenches can be inaccurate, so we recommend a precise torque screwdriver. Tighten the screws gradually and in a cross pattern.

Who do we recommend it for?

We recommend it to shooters who want to mount a scope with a 30 mm tube on a Picatinny-rail rifle and want more adjustment reserve at longer distances. It is a good choice for modern rifles with a long rail where the scope has to sit further forward, and for those who prefer a rigid one-piece mount. We do not recommend it for rifles with Weaver or dovetail rails.

User feedback

On the manufacturer's webshop, the one-piece 20 MOA version has received about 65 reviews, roughly 83% of them five-star. Most buyers praise the machining quality, easy installation and value for money. A US buyer checked the concentricity of the rings with a mandrel and found it accurate, with no visible deflection of the cantilever under load. A UK buyer reports that a Pard DS35 sits firmly in the mount, and a German buyer used it with an HD 2-12X24 SFIR scope. A few reviews criticize the longer delivery time. The 0 MOA version of the series has received about 105 reviews (average approx. 4.8 stars) with a similar picture: good machining, a favorable price, and only rarely a manufacturing defect in a thread. This feedback summary partly draws on other versions of the series.

Source: customer reviews on the manufacturer's webshop (discoveryopt.com).

Join our Facebook and YouTube channels!

Have a question?

Contact us through the webshop and we will help you choose the best solution for your scope and rifle!

Recommended accessories

Alternatives

Similar products

Reviews

Be the first to review!

Write a review

Thanks for a detailed, helpful review!
Reviews are moderated before publishing.